Fold and Unroll

Fold and Unroll

Triangle-Strip Unroll

Triangle-Strip Unroll

Fold and Unroll

Cuts every curved face of a Solid or Surface into true triangle strips for rigid sheet (aluminium composite, polycarbonate, card, thin ply) that is folded facet by facet instead of bent. Neighbouring strip edges are staggered by half a row, so each strip is a zigzag of triangles that folds even where the surface curves one way (a cylinder becomes rings of folded triangles, a sphere becomes rings with triangle fans at the poles). Rows run along the direction the surface turns most. Every triangle keeps its true size; folds are dashed: blue mountain, purple valley (seen from outside). Planar faces (caps) come out whole, faceted to meet the strips. Strips are named A1, A2 ... (one letter per curved face), caps F1, F2 ...; every seam carries the same number on both strips, strip edges on a cap carry the cap name and the cap the strip name, and every other place where two pieces meet gets a number too. A strip that would overlap itself when flat is cut into numbered pieces; a trimmed face keeps only the cells that lie on it. With Tabs on, one side of every seam and every strip edge on a cap gets glue tabs. Every strip and cap carries fold data for the Fold Back Check.

Docs for v0.6.6, the latest version.

ID

fold-and-unroll-fold-and-unroll-triangle-strip-unroll

Group

Fold and Unroll

Keywords

unroll
strip
triangle
facet
fold
rigid sheet
dome
lampshade
fabrication
glue tabs
zigzag
origami
10 inputs, 5 outputs

Ports

Inputs

10

What the node takes in, from wires or typed values.

Geometry

Geometry

Solid or Surface (or a list); every curved face is cut into strips

Tri Strips

Number

Default 6

Strips per curved face (1 - 64)

Tri Rows

Number

Default 8

Facet rows along each strip (1 - 100); fewer rows = fewer, bigger facets

Swap Direction

Boolean

Default false

Turn the strips the other way (by default the rows run along the direction the surface turns most)

Tabs

Boolean

Default false

Glue tabs on the long sides of the strips: one side of every seam between strips (strip ends get none)

Tab Width

Number

Default 0

Glue tab width (0 = automatic, a quarter of the typical strip width)

Spacing

Number

Default 0

Gap between laid-out pieces (0 = automatic)

Text Size

Number

Default 0

Height of the strip names; numbers are 0.7 of it (0 = automatic, fitted to each strip)

Tab Shape

Curve

Optional: a curve that replaces the default glue tab when Tabs is on - its height equals Tab Width and its base fits the tab edge; a long edge takes a row of them, each close to the proportions of the shape (open curve: base from its start to its end point; closed curve: centred on the edge)

Tab Count

Number

Default 0

Tabs on each long side of a strip, spread evenly along it (0 = one per straight run). Tabs go on the long sides only

Outputs

5

What the node gives out, to wire into other nodes.

Pieces

Surface

Flat strips and caps laid out on XY

Cuts

Curve

Cut outlines, tabs included

Folds

Curve

Fold lines: blue mountain, purple valley; tab folds blue (dashed; solid zigzag lines when there are more than 1500 folds)

Engrave

Curve

Everything to engrave: names, seam numbers and the dashed fold lines

Edges

Curve

Every piece outline (without tabs) split into separate curves, in its own colour so it is not mistaken for a cut line. A strip gives [left, right, start, end]: left meets the previous strip, right the next one, the long edges run from start to end; caps are split at their corners

This node has no documentation beyond its description and ports yet.

History

First documented in v0.6.5

Nov 20, 2026

Versions before it were published before changes were recorded.