Six nodes for flat cut-and-fold nets, in one group: Fold and Unroll. Unroll Surface: flattens a Solid or Surface into a numbered cut-and-fold net, nothing stretched; panels named P1, P1.1...; Mesh Unfold switch for papercraft nets. Triangle-Strip Unroll: cuts curved faces into zigzag triangle strips for rigid sheet folded facet by facet. Fold Back Check: folds the flat pieces back into the form and tests every joint number (PASS / CHECK report). Refold Net: unfolds a polyhedral part into a net and folds it back with a slider. Dart Cutter: flattens a doubly curved face as one piece with darts to close. Unroll with Markings: carries curves drawn on a developable face onto the flat pattern.
4 nodes
4
Unroll Surface
Flattens a Solid or multi-face Surface into a cut-and-fold net laid out on the XY plane. Planar faces unroll exactly; curved faces become flat triangles that bend into each other. Nothing is stretched: doubly curved faces are split into strips that unroll exactly (set their number with Panels). Fold lines are dashed. Both sides of every cut edge that joins another edge get the same number, engraved inside the piece next to that edge. Every piece is named P1, P2 ... and every face of a piece P1.1, P1.2 ..., engraved in its roomiest spot, so the panels are easy to find when arranging and assembling. A list wired into Geometry is unrolled item by item and laid out side by side. Every piece that unrolls exactly carries fold data (its flat triangles with their 3D corners, joint numbers and engraved numbers) so the Fold Back Check can fold it back into the shape and test the numbering; pieces with a stretched face carry none. Single-Curve Sides draws every side of a piece as one curve (cut lines, Edges and the piece outline); a curve wired into Tab Shape adds interlocking tabs along every seam; the Edges output gives each piece outline as separate curves (strips: left, right, start, end). With Mesh Unfold on, the part is read as the simplest mesh instead (planar faces whole, cylinders and cones as straight strips, spheres as gores) and unfolded papercraft-style into as few pieces as possible, with mountain (blue) and valley (purple) folds - best for origami and paper products.
Triangle-Strip Unroll
Cuts every curved face of a Solid or Surface into true triangle strips for rigid sheet (aluminium composite, polycarbonate, card, thin ply) that is folded facet by facet instead of bent. Neighbouring strip edges are staggered by half a row, so each strip is a zigzag of triangles that folds even where the surface curves one way (a cylinder becomes rings of folded triangles, a sphere becomes rings with triangle fans at the poles). Rows run along the direction the surface turns most. Every triangle keeps its true size; folds are dashed: blue mountain, purple valley (seen from outside). Planar faces (caps) come out whole, faceted to meet the strips. Strips are named A1, A2 ... (one letter per curved face), caps F1, F2 ...; every seam carries the same number on both strips, strip edges on a cap carry the cap name and the cap the strip name, and every other place where two pieces meet gets a number too. A strip that would overlap itself when flat is cut into numbered pieces; a trimmed face keeps only the cells that lie on it. With Tabs on, one side of every seam and every strip edge on a cap gets glue tabs. Every strip and cap carries fold data for the Fold Back Check.
Fold Back Check
Folds the flat pieces of Unroll Surface or Triangle-Strip Unroll back into the 3D form, carrying every engraved name and joint number along, so a net can be checked before it is cut. Each piece is folded facet by facet about its fold lines (the angles come from the form, the facet shapes from the flat sheet) and then placed as a whole. Checks: every joint number must appear on two edges that meet after folding (green = they meet, red = gap or length mismatch, orange = the number appears only once, magenta = two pieces meet there but the edge has no number), every facet must keep its size and, with Target connected, the folded result must sit on the original form. Fold 0 = flat sheet, 1 = assembled; Explode pulls the assembled pieces apart. Report says PASS or CHECK with the numbers behind it.
Refold Net
Unfolds a part into a net and folds it back up with the Fold slider: 0 = flat net, 1 = the closed part. Every flat panel turns about the edge it shares with its parent panel in the net - handy for checking a net and for folding animations. Planar faces stay whole. Single-curved faces (cylinders, cones, straight lofts) are cut into flat strips along their straight lines and roll up in one piece. Double-curved faces (spheres, domes, tori) are cut into gores joined along the middle, or with Triangle Strips on into rings joined along one column; every facet keeps its true size, so the folded part is faceted. Facets sets how finely curved faces are cut. With On XY on, the net lies flat on the XY plane at Fold 0 and the part stands on it at Fold 1. Flat pieces that carry fold data (the Pieces output of Unroll Surface or Triangle-Strip Unroll) are folded along their own fold lines instead: Fold 0 = the piece where the unroll node laid it, Fold 1 = back on the form.